Patch Panel Patch Cord for Internet and Telecommunications Commercial Project YH00

Computer motherboard parts installation and data line, the installation of the power cord plug is relatively simple, the average person is easy to master, but the chassis and motherboard control connection has some difficulty, if wrong is not unable to boot is not on, so as a computer enthusiasts must understand this problem:
Panel connection:
If you don't know which pin to insert, carefully look for near, each motherboard has instructions. First look for the pin below, if not carefully find near.
1. power switch connection line
2. reset switch connection line
A: yes, sir When connecting, first find two pin plugs labeled " resetsw" in white and blue, and then plug them into the pins labeled " resetsw" or " RSR" on the motherboard.
3. power indicator cable
Reminder: the power switch connection line and the reset switch connection line can be inserted without paying attention to the positive and negative problems of plug - in, and can be inserted in any way. But because the power indicator light side wiring is used to display the work and rest of the light secondary tube, so the connection is directional. Some boards will be labeled " pled +" and " pled -", we just connect the green end corresponding to the pled + pin, white line connected to the pled - pin.
4. hard drive indicator cable
A: yes, sir Note the directionality when inserting. General motherboard will be marked with " HDD led +", " HDD led -", the red end of the corresponding connection on HDD led + pin, white on the pin marked with " HDD led -".
5. speaker connection
Red plug positive, black plug negative. But the facts have proved that the two lines are both positive and negative.
Power switch: white + positive, brown - negative positive and negative plug can be
A According to its working principle, can be regardless of positive and negative poles, plug in can be used.
The following method is ok, just take care when connecting the USB cable, other lines can try to connect.
1 power switch connection
When connecting the power switch connector, first find the label " power" from the chassis panel connector
Sw " two pin plug, white brown two colors, and then insert on the motherboard marked" PWR
Sw " or" rwr " on the pin.
2 reset switch connection
Used to heat up a computer. When connecting, first find the label " reset"
Sw " two-pin plug, white and blue, respectively, and then insert on the motherboard marked" reset
Sw " or" RSR " pin is ok.
3 power indicator cable
First find the label " power"
Led " three pin plug, a line in the middle of the empty, two ends are white and green color respectively, and then insert it on the motherboard marked" PWR led " or" p
Led " on the pin.
Reminder: the power switch connection line and the reset switch connection line can be inserted without paying attention to the positive and negative problems of plug - in, and can be inserted in any way. But because the power indicator light side wiring is used to display the work and rest of the light secondary tube, so the connection is directional. " p" is indicated on some boards
Led + " and" p led - ", we just connect the green end corresponding to the p led + pin, white line connected to p.
Led - pin.
4 hard drive indicator cable
First find the two plugs labeled " h d d led" and connect them in white and red. insert them on the motherboard labeled " HDD"
Led " or" IED led " on the pin. Note the directionality when inserting. General motherboard will be marked with " HDD led +", " HDD led -", the red end of the corresponding connection on the HDD
Led + pin, white on HDD
Led - " pin.
5 speaker connection
First find the " speaker" four-pin plug, the middle two lines are empty, both ends are red and black two colors, insert it on the motherboard marked " peak er" or " spk" pin. Red plug positive, black plug negative.
Actual
Power switch: white + positive, brown - negative positive and negative plug can be
Reset switch: white and blue two colors, positive and negative plug can be casually.
Power switch: green plug in p
Led + pin, white on the p led pin.
Hard drive indicator: green in " pled +" and white in " HDD"
Led - " pin.
Speaker: red plug positive, black plug negative.
Take a closer look at the plugs on the chassis and basically label them as follows.
1. power SW also has a name pw
Sw ( this is the chassis power switch, used for chassis button control on and off ), on the motherboard will have the corresponding interface, plug in. if you don't understand can read the manual, the above object is very clear ( the same below ). positive and negative plug it doesn't matter, won't burn anything.
2. reset
Sw ( chassis reset key ) is used to restart the computer. it doesn't matter if the positive and negative poles are reversed. it doesn't burn.
3. HDD led some also called ide led
This is usually used to connect to the hard drive and show the hard drive working state. this plug-in still doesn't matter, but the hard drive light will not be on, if found not bright, change the order.
4. port + port - some standard p +
P - ( power indicator )
These two needles will usually be separated, the middle may be empty a needle. but some motherboard is connected together. also need to refer to the manual. some chassis cable will do together, empty a needle in the middle. plug it doesn't matter, if you turn on the computer power light is not on, change the order.
Speaker
This is the chassis horn power supply, is used to prompt the user the working state of each component. usually for two rows, eight needle settings, lack of a needle in the middle, can be found in the motherboard instructions, some motherboard will have jumper cap, pull it out, and the chassis plug wire will plug one of the holes, plug is impossible to insert.
6. audio
Chassis front audio pins. according to the instructions can still be easily inserted. it will be very clear to tell you the location and direction of the pin. if you find jumper cap pulled out. plug back found not working can also change direction. does not damage the hardware. some chassis without front audio interface, you don't need to consider.
7. front USB pin ( very important! - no! - no! ), plug this, you almost don't have the opportunity to test the plug didn't plug back, plug back later when you use the USB device, light burn out the USB device, heavy motherboard damage! So be sure to distinguish the direction. USB pins and plugs are set to four pins and the lines are sorted to VCC ( + 5v )
Port - port +
Grond ( ground ). when inserting this must carefully check the instructions, the motherboard of the USB pin will be in accordance with the two rows of 10 - pin settings missing one. that is, the above 5 - pin, the following 4 - pin, have a plenty of the opposite. novice plug in before the first line of the lack of needles, as long as find VCC corresponding jack can easily connect well. motherboard instructions will have detailed instructions, distinguish direction. if you are not sure don't plug in. so don't pay a heavy price. but there is a trick of Xiao Xiao, when you are not sure whether to plug in the reverse, you can do the following: hand hold the USB cable, power on, boot, insert USB devices
Finally, it is important to note that not every pin on the motherboard needs to be plugged in, depending on your chassis and the equipment you need. the above is the most common wiring method. don't pull off the jumper cap on the motherboard easily, unless you need. otherwise it may cause damage to the motherboard.