IEC60335-2-9 Aluminum Electronic Test Equipment 1.8KG Test Vessel SN1130

IEC60335 Aluminum Electronic Test Equipment 1.8KG Test Vessel SN1130

Product information:

This test vessel conforms to standard requirements of IEC 60335-2-6 clause 21.102, IEC 60335-2-9 clause 21.101.
The vessel has a flat copper or aluminum base over a diameter of 120mm±10mm, its edges being rounded with a radius of at least 10mm. It is uniformly filled with at least 1.3 kg of sand or shot so that the total mass is 1.8 kg ±0.01kg.

Technical Parameters:

The vessel has a flat copper or aluminum base over a diameter of 120mm±10mm, its edges being rounded with a radius of at least 10mm. It is uniformly filled with at least 1.3 kg of sand or shot so that the total mass is 1.8 kg ±0.01kg.

Operation Steps:

• Surfaces of hotplates of glass-ceramic or similar material shall withstand the stresses liable to occur in normal use.
• Compliance is checked by the following test.
• Induction wok hotplates are tested with a wok pan that is supplied by the manufacturer with the induction wok hotplate at the point of sale. The wok pan is filled with sand or shot so that the total mass, including the mass of the wok pan, is equal to 1,8 kg ± 0,01 kg.
• The hotplate is operated at rated power input with its control adjusted to the highest setting Induction hotplates are operated as specified in Clause 11. When steady conditions are established, the hotplate is switched off and a vessel with its base horizontal is dropped from a height of 150mm onto the cooking zone. The vessel has a copper or aluminum base that is flat over a diameter of 120mm+10mm, its edges being rounded with a radius of at least 10mm. It is uniformly filled with at least 13kg of sand or shot so that the total mass is 1.80 kg ± 0.01 kg.
• The vessels dropped 10 times onto each cooking zone. It is removed and the appliance is operated at rated power input until steady conditions are established.
• A quantity of 1^+0.1 of water containing approximately 1 % NaCl is poured steadily over the hotplate
• The appliance is then disconnected from the supply. After 15 min. all excess liquid is removed and the appliance is allowed to cool to approximately room temperature. The same quantity of the saline solution is poured over the hotplate after which excess liquid is removed again.
• The surface of the hotplate shall not be broken and the appliance shall withstand the electric strength test of 16.3.

Sinuo is an innovation manufacturing company, specializing in the research and development and sales of laboratory construction and testing equipment for electrical appliances (covering the construction of energy efficiency and performance laboratories, as well as supplementary waterproof testing laboratories, materials flame-retardant laboratories, basic general testing equipment, etc.), Sinuo aims to provide clients with complete laboratory construction, system integration, R&D, rectification and after-sales service, and strive to be the leader of one-stop service for laboratory construction in the field of electrical appliance testing.

Sinuo  products are composed of all kinds of testing equipments as per standards of IEC/ BS/ EN/VDE/UL/ ISO..., such as household appliances testing equipment, energy efficient testing laboratories and comprehensive performance test system for household appliances, battery testing equipment,  automotive testing equipment, luminaries testing equipment,IP code testing equipment, environmental test chamber, flammability test chambers, EMC testing equipment and etc.

Sinuo employees include a highly trained staff of engineers for sales and service, that are committed to offer satisfactory products and prompt service to all home and abroad customers.

Sinuo cooperate with many research institutions and schools to enable our techincal capacities. Sinuo has two own factories, one is in Guangzhou, the other is in Dongguan, and authorized agents and representative offices in Korea, South Africa, Egypt,Pakistan and Philippines.

Sinuo combines all the R/D and production advantages, contributes to provide perfect, high-end and systematic electrical appliance testing laboratory solutions, products and services for corporate customers, universities and third-party laboratories. Our clients include Bureau Veritas, CSA, Intertek, TUV Rehiland, TUV SUD, SGS, etc.