IFM Flow sensor SA5000 SAD10XDBFRKG

Product characteristics
Number of inputs and outputs Number of digital outputs: 2; Number of analogue outputs: 1 Process connection threaded connection M18 x 1,5 internal thread
Application
Special feature						Gold-plated contacts
Media						water; glycol solutions; air; oils
Note on media				low-viscosity oils with viscosity: ≤ 40 mm²/s (40 °C)
				high-viscosity oils with viscosity: > 40 mm²/s (40 °C)
Medium temperature		[°C]		-20...90
Pressure rating		[bar]		100
Pressure rating		[Mpa]		10
MAWP (for applications according to CRN)		[bar]				100
ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — SA5000-01 — 26.04.2021 —

SA5000
Flow sensor
SAD10XDBFRKG/US-100
Electrical data
Operating voltage			[V]			18...30 DC
Current consumption			[mA]	< 100
Protection class				III
Reverse polarity protection				yes
Power-on delay time			[s]	10
Inputs / outputs
Number of inputs and outputs				Number of digital outputs: 2; Number of analogue outputs: 1
Outputs
Total number of outputs						2
Output signal				switching signal; analogue signal; frequency signal; IO-Link; (configurable)
Electrical design						PNP/NPN
Number of digital outputs						2
Output function				normally open / normally closed; (parameterisable)
Max. voltage drop switching output DC			[V]			2.5
Permanent current rating of switching output DC			[mA]	250
Number of analogue outputs				1
Analogue current output			[mA]	4...20; (scalable)
Max. load			[Ω]	350
Short-circuit protection				yes
Type of short-circuit protection				pulsed
Overload protection				yes
Frequency of the output [Hz]						0...1000
Measuring/setting range
Probe length L			[mm]			45
Operating mode				relative; absolutely liquid; absolutely gaseous; (absolute: reference measurement recommended)
Note on factory setting				Operating mode: relative
Liquids
Setting range Greatest sensitivity			[m/s] [m/s]			0.04...6 0.04...3
Gases
Setting range Greatest sensitivity			[m/s] [m/s]			0...200 2...100
Temperature monitoring
Measuring range Resolution			[°C] [°C]			-20...90 0.2
ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — SA5000-01 — 26.04.2021 —

SA5000
Flow sensor
SAD10XDBFRKG/US-100
Accuracy / deviations Flow monitoring
Temperature drift	[cm/s x 1/K]					0,003 m/s x 1/K (< 20 °C; > 70 °C)
Temperature gradient [K/min]				100
Accuracy				± (7 % MW + 2 % MEW); (for relative mode in the range of maximum sensitivity under the following conditions:; water: 20...70 °C; inlet length: 1.5 m; DN25 (DIN 2448); mounting position according to instructions; Accuracy can differ for other media and mounting positions.)
Repeatability				0,05 m/s; (water; flow velocity: 0,05...3 m/s)
Temperature monitoring
Temperature drift ± 0,005 K/°C Accuracy [K] ± 0,3 / ± 1; (water; flow velocity: 0,3...3 m/s / air; flow velocity: > 10 m/s)
Response times Flow monitoring
Response time [s]				0.5; (T09; water; glycol: 0,8 s; air: 7 s; oil: 1,8 s; each T09)
Temperature monitoring
Dynamic response T05 / T09 [s]				1,5 (T09); (water; flow velocity: 0,3...3 m/s)
Software / programming
Parameter setting options				hysteresis / window; normally open / normally closed; switching logic; current/ frequency output; medium selection; Damping; Teach function; display can be rotated and switched off; standard unit of measurement; process value colour
Interfaces
Communication interface						IO-Link
Transmission type						COM2 (38,4 kBaud)
IO-Link revision						1.1
SDCI standard						IEC 61131-9
Profiles				Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis
SIO mode				yes
Required master port type				A
Process data analogue				2
Process data binary						2
Min. process cycle time [ms]						3
Supported DeviceIDs				Type of operation			DeviceID
				Factory setting / ModE = (REL)			533
				ModE = (LIQU)			540
				ModE = (GAS)			547
Operating conditions
Ambient temperature [°C]						-40...80
Storage temperature Protection			[°C]			-40...100 IP 65; IP 67
ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — SA5000-01 — 26.04.2021 —

SA5000
Flow sensor
SAD10XDBFRKG/US-100
Tests / approvals
EMC				DIN EN 60947-5-9
Shock resistance				DIN EN 60068-2-27			50 g (11 ms)
Vibration resistance				DIN EN 60068-2-6			20 g (10...2000 Hz)
MTTF [years]				132
UL approval				UL Approval no.			I003
Mechanical data
Weight [g]						314
Materials					stainless steel (1.4404 / 316L); stainless steel (1.4310 / 301); PBT-GF20; PBT-GF30
Materials (wetted parts) Process connection					stainless steel (1.4404 / 316L); Gasket: FKM threaded connection M18 x 1,5 internal thread
Displays / operating elements
				Display unit			6 x LED, green (%, m/s, l/min, m³/h, °C, 10³)
Display				switching status			2 x LED, yellow
				measured values			alphanumeric display, red/green 4-digit
Remarks
Remarks				MW = measured value
				MEW = Final value of the measuring range
Pack quantity						1 pcs.

Product Tags:

IFM SA5000 flow sensor

IFM pressure sensor with warranty

SA5000 industrial flow sensor

IFM Flow sensor SA5000 SAD10XDBFRKG

Send your message to this supplier


*From:	Your email address is incorrect!
*To:	Xiamen ZhiCheng Automation Technology Co., Ltd
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	IFM Pressure Sensor
Brand Name:	IFM
Model Number:	SA5000
Certification:	3C
Place of Origin:	GERMANY
MOQ:	1
Price:	$400/piece
Payment Terms:	T/T
Supply Ability:	1piece in stock
Delivery Time:	3 day
Packaging Details:	1505050mm
Probe length L[mm]:	45
Weight[g]:	257
Dimensions[mm]:	Ø 34 / L = 142