RFID Read Write Head With TCP IP Port LED Display 5Pin M12 A Coded
Male Connector
Product Attributes
| Attribute | Value |
|---|
| Series | Q80 Series |
| Description | RFID HF Read/write Head |
| Operating Temperature | -30℃~+70℃ |
| Voltage Rating | 18-30V |
| Interface | M12 8 Pin Male Connector |
| Operating frequency | 13.56MHz |
| Supply voltage | 9-30VDC |
| Measuring Range | 0~150mm(Related to the tags) |
Product Description
RFID Read Write Head With TCP IP Port LED Display 5Pin M12 A Coded
Male Connector
Advantages
- High protection level and strong corrosion resistance, can be used
in harsh industrial environments
- High reading and writing speed, speeding up factory production
rhythm and improving production efficiency
- Supports RS232, RS485, TCP/IP, Modbus RTU, Modbus TCP
communication, and can be quickly integrated into industrial
networks such as PROFINET, EtherCat and Ethernet/IP with our
Gateway Module
- High stability and reliability, 7*24h operation
| Design | ① LED status display
② Power supply and communication interface |
|---|
| Area of application | Identification tasks on small assembly lines in harsh industrial
environments. Usually used in new energy, automobiles, home
appliances and other industries |
|---|
Electrical Interface
KRH-Q80G with RS-232 interface, using a 5Pin-M12-ACODED-Male
connector, the pin assignment is shown below.
| Connector | Pin | Assignment | Description |
|---|
 | 1 | +24V | Power supply positive |
| 2 | TX | RS-232 TX |
| 3 | 0V | Power supply negative |
| 4 | RX | RS-232 RX |
| 5 | NC | Not connected |
LED Operating Display
The operational statuses of the reader (KRH-Q80G with TCP/IP
interface) are displayed by the LEDs. The LED can adopt the colors
blue, red or yellow and the statuses off, on, flashing.
| Name | Color | State | Description |
|---|
| SYS | Blue Red | Off | The reader is power off. |
| Blue LED on | The reader is powered on and working properly. |
| Blue | Blue LED flashing | The reader is in BOOT mode. |
| Red | Red LED on | Reader self-test failed. |
| Red | Red LED flashing | Reader software runs abnormally. |
| LINK | Blue Red | Off | No connection established. |
| Blue LED on | Connection established. |
| Blue | Blue LED flashing | Valid instructions were received and executed successfully. |
| Red | Red LED on | Hardware failure. |
| Red | Red LED flashing | Valid command received but execution failed. |
| TAG | Blue Yellow | Off | No Tags was detected in the identification area. |
| Blue LED on | Tags was detected in the main identification area (RSSI signal is
the strongest). |
| Blue | Blue LED flashing | Tags was detected in the secondary identification area (RSSI signal
is medium). |
| Yellow | Yellow LED on | Tags was detected in the critical identification area (RSSI signal
is weak). |
| Yellow | Yellow LED flashing | Tag was detected between the critical identification area and the
non-identification area (RSSI signal critical). |
Reliable Identification Area
The tag should be in the center area of the sensing range as shown
below.
Metal-free Area
The KRH-Q80G can be flush-mounted in metal. Allow for a possible
reduction in the field data. To avoid any influence on the field
data, the distance "D" should be kept to ≥30mm.
Minimum Distance Between KRH-M30G Readers
KRH-Q80G side by side: To avoid any influence between the readers,
the distance "D" should be kept to ≥300mm.
KRH-Q80G face-of-face: To avoid any influence between the readers,
the distance "D" should be kept to ≥400mm.
Technical Data
| Order No. | KRH-Q80G-TCP |
|---|
| Radio Frequencies |
|---|
| Operating frequency | 13.56MHz |
| Antenna | Intergrated |
| Read/Write range | 0-150mm (Related to the tags) |
| ISO standard | ISO 15693 |
| Electrical Data |
|---|
| Supply voltage | 9~30VDC |
| Current consumption | <100mA@24V |
| Communication interface | TCP/IP |
| Transmission speed | 10 / 100M adaptive Ethernet |
| Transmission distance | Cat5e and above shielded twisted pair, <100m |
| Connector | 8Pin-M12- ACODEDMale |
| Permitted ambient conditions |
|---|
| Operation temerature | -30℃~+70℃ |
| Storage temperature | -40℃~+85℃ |
| Degree of protection | IP67 according to EN 60529 |
| Shock resistance | 7M2,500 m/s2,according to EN 60721-3-7 |
| Vibration resistance | 7M2,200 m/s2,according to EN 60721-3-7 |
| Torsion and bending load | Not permitted |
| Mechanical specifications |
|---|
| Housing Material | PC + ABS |
| Housing color | Black |
| Weight | About 185g |
| Dimensions | 80 x 80 x 30 mm |
| Type of mounting | 4 X M4 screws, the length of the screw should be ≥ 20 mm |
| Thread code | M30 x 1.5 |
| LED display | 4 x LED, blue 2 x LED, red 2 x LED, yellow |
| Standards, specifications, approvals |
|---|
| Proof of suitability | CE FCC RoHS WEEE |
13.56MHz RFID Recognition System Read Write Head With RS-485 LED Display And M30
