HDPE Seamless Electro fusion Sleeves Tape for Preinsulation Pipe Joints Waterproof and Durable

Huashida HDPE Electro Fusion Sleeves is a pipe interface welding material: high-quality HDPE sheet is cut into sheets that meet the required length, width, and thickness according to actual needs, and then combined with special electric heating wire mesh through special heat sealing equipment. It combines the high tensile toughness strength and shrinkage rate of both electrofusion sleeves and heat shrinkable sleeves.

1. District thermal heating system construction,
2. Pre-insulated pipes field joint welding and oil pipes joint welding;
3. Preinsulated bonded pipe system for directly buried hot water networks;
4. Three PE/PP layers with foam jacket insulation pipes connection;
5. Steel pipes anti-corrosion etc.

Seamless hot melt sleeve process:

1.The working pipe is heated (expands)

2. The outer protective pipe is heated (tightened)

3. Expand internally and contract externally, with a tight combination

Construction precautions for seamless heat shrinkable joint sleeves

1. Remove dirt. Wipe the surfaces at both ends of the pipe clean and gently sand it with sandpaper.

2. Preheat the temperature at both ends of the pipe to 60°-70°, take off the adhesive tape and place it in an appropriate position, then remove the isolation film.

3. The self-adhesive tape should be placed at the appropriate position on the outer edge of the seamless heat shrinkable joint sleeve. Use a ruler to find the right position and make the marking for pasting.

4. Pull back the seamless heat shrinkable joint sleeve to the appropriate position.

5. Bake the edges 10cm high over high heat. First, bake the top until it softens, then the sides, and finally the bottom. After baking one side, bake the other side. It's best for two people to bake each other at the same time. Repeat this process back and forth

6. During on-site field construction, pay attention to the crosswind and flame direction. The hot spot must not be exposed to the suspended area (in the middle of the joint).

7. It is essential to allow the softened heat shrinkable joint sleeve that has been baked to cool down for a certain period of time. Only in this way can it shrink more tightly

8. Finally, seal both ends with heat shrink tape and inject polyurethane in time. If the product is exposed to the sun for a long time or is placed on the pipe without construction, it will shrink, causing it to seize up with the pipe and be impossible to remove. Therefore, construction and storage should be carried out in accordance with the requirements!

9. Do not bake horizontally. Instead, swing the spray gun up and down to bake

10. Store the product in a cool and well-ventilated place, away from direct sunlight

11. Place horizontally to prevent deformation.

Construction scene photos

Shipping photos

International Trading show

Certifications

Clients case

1. company profile

Qingdao Huashida Machinery Co., Ltd. is located in Qingdao High & New Technology Industrial Area- Qingdao Huashida industrial Park, covers an area of about 4000 square meters. We have tens of years experience in plastic pipe, sheet, and board extrusion lines, and pipe joints and welding tools such as heat shrinkable sleeve, Electro fusion sleeve etc.

2. main products

Our main products include as following,HDPE PU pre-insulation Jacket Pipe extrusion line,3PE steel pipe anticorrosion&coating machinery,Rubber&plastic foam flexible insulation tube/sheet production line,HDPE water supplying pipe extrusion line,PE PP sheet board extrusion line,Heat shrinkable sleeve production line,Hollow wall spiral pipe production line,Plastic welding rod extrusion line,Radiation cross-linked PE heat shrinkable sleeve,Electro fusion tape,Portable extrusion welder.

Our machines make products what are widely used as jacket pipe of PU foam insulation pipe in municipal heating pipe system; Municipal water supplying and drainage pipeline; Oil and gas pipeline; Pipe joints of plastic drainage water pipes, PU foam insulation pipelines, 2PE/3PE oil and gas pipelines;
Besides manufacturing machines, we also make Heat shrinkable sleeves and electro fusion sleeves and plastic welders, which are widely used as pipe joints and sealings of plastic drainage water pipes, PU foam insulation pipelines, 2PE/3PE oil and gas pipelines;

4. Our certificates and Patents

5. Global market
Our purpose is to supply highest cost-effective products and the most suitable solutions to our clients, as well as intimate help and service, on this basis we reach a win-win situation.
For over 14years We have exported to many foreign countries, such as Russia, Iran, Turkey, U. A. E, Sudan, Ukraine, Uzbekistan, Azerbaijan, South Asia, Poland etc.

6. Core Team

The guarantee period is 12 months from the date of installing, but no more than 14 months from the date of delivery. After this period we are obliged to provide with lifelong service at the expense of Buyer.During the warranty period we are responsible to provide trouble shootings and help the customer to solve the problems, provide spare parts which are broken, except breakings caused by the Buyer.We will provide the technical service train the workers from the buyers for free.We can also send technicians to the buyer's companies abroad for help installation and testing the lines. But the buyer shall pay for the round trip tickets, accommodation, transportation, medicine treatment and insurance of the technicians in foreign countries and some salary accordingly.