FPV Transmission 1.7Ghz 6W FPV VTX Video Link 8CH Support IRC Tramp 25mW 800mW 6000mW Adjustable Power

FPV Transmission 1.7Ghz 6W FPV VTX Video Link 8CH Support IRC Tramp 25mW 800mW 6000mW Adjustable Power

I.Main Features

l Channels 8CH;

l Control Protocol: IRC Tramp, supports OSD tuning;

l Allows users to define custom frequencies within 1680-1960MHz using IRC Tramp tuning software;

l Power: PIT / 25mW / 800mW / 6000mW;

l Efficient DC/DC power input: 7-36V;

l Supports 5V voltage output;

l Supports installation on flight tower (30.5*30.5MM / M3 mounts)

II.Product Specifications

l Transmitter (Air Unit):

l Input Voltage: 7-36V DC (2-6S)

l Output Voltage: 5V/0.5A

l Weight: 21.5g (excluding antenna)

l Dimensions (L*W*H): 37mm*46mm*17.5mm (including SMA connector and fan)

l Video Format: PAL/NTSC

l Number of Channels: 8

lChannel Selection: Frequency adjustment button (short press to switch)

lTransmission Frequency: 8CH (see frequency table)

l Power Adjustment: Power button (short press to switch)

l Power Levels: 3 levels - 25mW / 800mW / 6000mW

lAntenna Connector: SMA (external thread, internal hole)

l Modulation Type: FM

III.Transmitter Operation Instructions:

1.Frequency Table

Note: Ensure good contact with antenna at 800mW and 6000mW levels. Poor connection may damage the amplifier.

2.Short press “ Power” button to choose the power level repeat short press for recycle from 25mW ,800mW,

6000mW . The green light is the power indicator light, and its status is shown in the following figure. It flashes once for 25mW, twice for 800mW, and three times for 6000mW. Press and hold for 3 seconds to enter PIT mode, with the green light constantly on.

The lights correspond to two power levels respectively. After setting the corresponding power, the corresponding lights remain on constantly.

IV.Precautions:

l Install the antenna before powering on to avoid device damage.

l Select the appropriate operating Frequency and set the transmitting end and the receiving end to the same frequency (for details, see Frequency Table);

l High power output – avoid touching the casing during operation to prevent burns (heating is normal).

l Casing can be removed to reduce weight, but may lower transmission power due to heat.

l Input voltage: 7-36V (2-6S); do not exceed this range.

l Output: 5V/0.5A. Ensure your camera stays within this limit. Exceeding may damage the power module.

l 5V and 5V-OUT are output ports. Do not connect to power input or batteries to avoid damage.

Kimpok Technology is a leading of High-tech global enterprise in R&D and manufacturing. Company established in 2008 and located in Shenzhen China. Specializing in the provision of advance wireless microwave communication system to the broadcast, UAV, public surverillance and defense industries. By continuously investing in innovation and combining exceptional products and services, Kimpok offers superior solutions that enable our customers to do their jobs even more effectively.
Kimpok Technology has a very strong technical team and R&D capacity. we dedicated to developing the high level wireless mobile video surveillance system for application of Law enforcement and military, field forces, radar, R/C helicopter, security & protection, government departments, military, security systems, oil field, Vessel, large mines, factories and so on.
Last for 17 years, Kimpok Technology continually concentrate on researching and innovating in the wireless high speed mobile video transmission industry based in LOS/NLOS environments, especial for Unmanned aircraft vehicle(UAV), airborne area and soldier man-pack areas. COFDM modulation and FDD working mode transmitter/receiver are our demonstrable advantages. All the products production must be in very strict quality management by using US original (HP) spectrum analyzer and Germany (Rohde & Schwarz) Network Analyzer.
The transmitter and receiver are with Anti-jamming, high quality image, long range transmission distance, and have a highly appraise in this area. Company's developing and long-term programming is the key way for leading us to be the leader at this area, we always believe we can do it. We will continually concentrate on researching and innovating in the wireless microwave transmission industry.
Welcome to tell use your needs, we will try to meet your requirements and custom made a special device for you." Your support and suggestions are our motivation". We aim to provide our users worldwide exclusive advanced wireless videography system.

Testing Equipments:

Our customers: