| 3. Use Condition |
| Ambient Temperature Range | -25 +85 | | |
| Applicable Wire Sizes | AWG #2228 | | |
| Applicable PC board thickness | 1.6mm | | |
| 4. Appearance and Dimension |
| Appearance | Product surface without defect, dirt, crack, and mechanical damage;
Contact without rust, plating not oxides and not peeled | | |
| Dimension | According to drawings | | |
| Exchangeable | Exchangeable with same specification products | | |
| 5. Material |
| Terminal Contact | Phosphor bronze, 0.2mm thickness, Tin plating: 35 m | | |
| Housing Plastic | Nylon66 UL94V-0, Color: White | | |
| Pin | Brass, 0.50mm thickness, Tin plating: 2.55 m, Color: Beige | | |
| 6. Electrical Performance |
| Rated Voltage | 250V AC/DC | | |
| Rated Current | 2A AC/DC | | |
| Contact Resistance | Initial value 20 | 20m | Apply a maximum voltage of 20mV and maximum current of 100mA to the
Mate connector (Does not include wire resistance) |
| Insulation Resistance | 1000 M | 1000 M | Apply 500V DC (rms) for 1 minute between adjacent contacts |
| Withstand voltage | No breakdown or flashover | Apply 800V AC (rms) for 1 minute and the leakage current shall not
exceed 0.5mA to the adjacent terminal and ground of the mate
connectors | |
| 7. Mechanical Performance |
| Single contact insertion force | 6N | 6N | The housing together with the terminal ends with wafer matched at a
rate per minute to 253mm inserting force test |
| Single contact Withdrawal force | 0.5N | 0.5N | The terminal and the hole seat at a react per minute to 25 3mm
along the write direction are pulled out from the hole in the seat
capacity |
| Terminal crimping Wire strength | AWG#22: 50N, AWG#24: 30N, AWG#26: 20N, AWG#28: 13N | | Axial per minute to 25 3mm rate of the pullout force |
| Pin Retention Force | 15N | 15N | Exerts a force on the pin end at a rate per Minute 253mm until the
needle exit |
| Seat pull-out force | 15N | 15N | The housing together with the terminal ends with wafer matched at a
rate per minute to 253mm inserting force test |
| Durability | Contact Resistance 30m | 30m | Mate connectors up 30 cycles at a Maximum rate of 10 cycles per
minute prior to environmental test |
| Vibration | Current interruption: 1 sec Max, Contact Resistance 30m | | Amplitude: 1.5mm p-p, Frequency: 10-55-10Hz/minute, Duration: 2
hours for each direction (X, Y, Z axis) |
| 8. Endurance Characteristics |
| Thermal Aging | Appearance: No damage, Contact Resistance 30m | 30m | Temperature: 852, Period: 96 hours continuously |
| Temperature rise | | | Measure the temperature rise of contact when the maximum rated
current is passed |
| Constant Humidity | Appearance: No damage, Contact Resistance 30m , Insulation
Resistance 500m | 30m , 500m | Temperature:402 C, Relative humidity: 90-95% (RH), Period: 96 hours
continuously |
| Temperature cycling | Appearance: No damage, No breakdown or flashover | | One cycle consists of -55 3 C 30min, 85 3C 30min, room temp
10-15min transition. Total cycle: 5 cycles |
| Salt spray | Appearance: No damage, Contact Resistance 30m | 30m | Temperature: 353 C, Concentration: 51% NaCl solution, Period: 8
hours (post-stamping plating) or 24 hours (pre-stamping plating) |
| Solder ability | Soldering area: 90 % | 90 % | Solder temperature: 245 5C, Immersion period: 3 0.5S |
| Resistance to soldering heat | Appearance: No damage | | Manual soldering: 350 5 for 3 0.5S. Wave soldering: 2305 for 50.5S.
Position: 1.5mm from conductor/fixing piece end. |
