5 Shore A RTV 2 Addition Cure Silicone Mold Rubber For Strawberry
Candy
Technical datasheet of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold Rubber| Item No. | MCPLA-L05 |
| Color | Translucent/can be customized |
| Viscosity ( cps,approx.) | 3500-6000 |
| Mix ratio (A:B) | 1:1 |
| Working time(at 25ºC ,minutes) | 30-40 (can be adjusted) |
| Curing time(at 25ºC,hrs,approx.) | 4-6 (can be adjusted) |
| Hardness Shore A(after 24 h) | 5 |
| Tensile Strength(Mpa,after 24 h) | 3.2 |
| Elongation(%) | 650 |
| Tear Strength(N/mm) | 12 |
| Linear Shrinkage (%) | 0. 1 |
Characteristics of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold RubberConvenient to operate because the RTV propertyEasy to mix due to the low viscosity (4000~6000Cps)High duplication because of high tear and tensile strengthLong shelf life with low shrinkageCan be accelerated for rapid cureApplication of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold Rubber1.A range of materials can be cast into the cured silicone mold:polyurethane and other reactive resinsSmall pieces of cement,plaster,concrete products.Food like chocolate,fondantsWax,candle,soap;Low melt metal2.casting body parts,shoe insole,cloth label,texture coating.
Instructions of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold Rubber1. Mixing the two componentsAccording the mixing ration 1:1 weighting A and B, the two
components may be thoroughly mixed either by hand or using a
low-speed electric to minimize the degassing of bubbles and to
avoid any temperature increase.Note: It is also possible to use a special mixing and dispensing
machine for the silicone components, further information is
available upon request.2. MouldingThe mixture should be degassed preferably at 30 to 50 mbar to
eliminate any entrapped air. If a dispensing machine is used, the
two components are degassed separately prior to mixing. The
silicone mixture expands to 3-4 times of its initial volume and
bubbles rise to the surface. The bubbles progressively disappear
and the mixture returns to its initial volume after 5 to 10
minutes. Wait a few minutes to complete the degassing and then
flash the vacuum. The silicone is ready for pouring, either by
gravity or under low pressure.Note: Flashing the vacuum once or twice accelerates the degassing.
It is recommended to use a container with a high diameter/height
ratio (3 to 4 times of the initial volume)3. PolymerisationThe curing may be slowed down at lower temperature or accelerated
by applying heat.Note:1.Contamination from sulfur (e.g., sulfur-based clay), amines, tin
compounds, cured polyester resin, some paints and some silicone
rubbers may inhibit surface cure of platinum-cured rubbers.2.Apply a release agent, Although not usually necessary, a release
agent will make demolding easier when casting into most surfaces.Note: It is strongly recommended that entrapped air be removed in a
vacuum chamber, allowing the mix to completely expand and then
collapse. After a further 1-2 mins under vacuum, the mix should be
inspected and can be used if free of air bubbles. A volume increase
of 3-5 times will occur on vacuum de-airing the mixture. So a
suitably large container should be chosen.
Storage of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold RubberWhen the platinum RTV-2 Silicone Rubber is stored at or below 30 °
C (85° F) in the original unopened containers, RTVsilicone base and
C520 curing agent have a usable life of
12 months from the date of production.
Packaging of 5 Shore A RTV 2 Addition Cure Silicone Food Grade Mold Rubber1kg=504kg pallet, 5kg/drum=600kg/pallet, 10kg, 20kg per plastic
drum=480kg per pallet
200kg per drum, 800kg per pallet. Other types of package, please
check with our sales representative.
Professional factory of RTV2 silicone:
We are manufacturer, and specialized in manufacturing different
hardness, different viscosity silicone rubber series, we are
competitive in price with good quality.
Should you have any question, please feel free to contact us.
100:2 Tin Cured RTV2 Silicone Mold Rubber For Flower Pot Mold
