Product Details
Company Profile

Dip Switch Design Compact ON/OFF Motion Sensor For Ceiling Light And Tri-proof Light

【Product Features】

Low impedance microwave antenna, can effectively resist interference from 5G, WiFi, Bluetooth and other wireless signals.
Adopting patented di-pole antenna, with strong environmental adaptability and no detection blind area.
Products in batch production comply with RED certification, and the entire lamp certification is guaranteed.
Dip switch design, users can easily set parameters according to needs
Long strip shell design, suitable for tri-proof light and ceiling lamps
Maximum installation height of 6 meters
5 years warranty

【Parameters】

Input
Rated Voltage	220-240Vac 50/60Hz
Stand-by Power	≤0.5W
Surge Test	1KV(L/N,EN61000-4-5)
Output
Output Signal	ON/OFF
Type of Load	Inductive or Resistive
Load Capacity	400W@230Vac(Inductive) ; 800W@230Vac(Resistive)
Max. Surge Capacity	7A relay 50A(50% Ipeak, twidth =200uS, 230Vac full load, cold start);
Sensor Parameters
Working Frequency	5.8 GHz ±75MHz, ISM wave band
Transmitting Power	1mW Max.
Detection Area(Radius)	Ceiling mounting height 3m: r≥4m@0.3m/s, r≥2.5m@1m/s; Wall mounting height 3m: r≥5m@0.3m/s, r≥4m@1m/s Test condition: Set 100% sensitivity, open 60㎡ indoor area.
Mounting Height	3m (6m Max)
Hold time	5s/30s/90s/5min/20min/30min (Dial code)
Detection Area	100%/75%/50%/25%(Dial code)
Daylight Sensor	Normal Daylight	2Lux/10Lux/30Lux//50Lux/Disable(Dial code)
Operating Temperature	-25℃…+60℃
Storage Temperature	-40~80℃ Humidity: ≤85% non-condensing
Certificate Standards
Certified	CE, RED
Environmental Requirements	Comply with RoHS 2.0 Reach
IP Rating	IP20
Other
Remote Model	MH10; MH16; MH03
Wiring	Press-in Type Terminals, wire diameter: 0.5-0.75mm²
Installation	Built-in
Package	Bubble bag+Clapboard + Carton(K=A)
Net Weight	38 ±2g
Lifetime	5 years warranty@Ta

【Function】

ON/OFF function	Light control Disable or external brightness value is lower than the set value. When the microwave sensors detects the movement of an object, the sensor triggers and enters the light-on state. It maintains the light-on state after a delay and then enters the light-off state.
Two-step dimming function	N/A
Three-step dimming function	N/A
Daylight harvesting	N/A
Daylight priority	N/A

【Product Information】

Dimension(units: mm)

Function Detection Area Hold Time Daylight Sensor Dial code 1 2 Detection area 3 4 5 Hold time 6 7 8 Light control value Ⅰ ON ON 100% ON ON ON 5s ON ON ON 2Lux Ⅱ - ON 75% - ON ON 30s ON ON - 10Lux Ⅲ ON - 50% ON - ON 90s - ON - 30Lux Ⅳ - - 25% - - ON 5min ON - - 50Lux Ⅴ ON ON - 20min - - - Disable* Ⅵ - - - 30min

【Initialization】

The light will be turned on 100% brightness after power on, and will be turned off after 10 seconds. During initialization, no external motion sensing signal will be detected.

【Default Setting】

Sensitivity: 100% Hold time: 5s Daylight sensor: Disable

【Application Notice】

The sensor should be installed by a professional electrician. Please turn off the power before installing, wiring, changing the setting of the DIP switch.
Sensitivity area is related to moving speed of objects, size of moving objects, mounting height, mounting angle, working environment, reflecting materials and etc.. Given detecting area is typical value that was measured by 165cm/65kg testers in an indoor open environment.
The detection area of the microwave sensor when installed on the wall will be greatly increased compared to when installed on the ceiling. If adopts wall ceiling, please reduce the sensitivity or contact our company to confirm the usage settings. The daylight thresholds are measured on a sunny day without shadow and in an ambient light diffuse reflection status. Different environment and climate cause different brightness values that daylight sensor measures.
Sensor parameters may need to be reconfigured in different installation environments, please refer to the following instructions or contact the manufacturer.
Sensor is for indoor use only. The waterproof effect for outdoor or half-outdoor use will be affected. Wind, rain, and moving objects may cause false triggering.
The installation height of the sensor product cannot exceed 6 meters, and the optimal height is 3 meters. The distance between the two sensors should be greater than 3m.
When the sensor is installed in a metal lamp, on a metal reflective surface, or in a small closed environment, the microwave will be reflected multiple times and cause false triggering. Please reduce the sensitivity of the sensor or contact the manufacturer for technical support.
Please make sure that there are no moving signals such as fans, DC motors, sewer pipes, air outlets, etc. around the sensor, otherwise the sensor may cause false triggering.
Microwaves cannot penetrate metal. Do not place product in a closed or a half-closed metal lamp. Neither metal nor glass is not allowed to cover above the product.

Product Tags:


*From:	Your email address is incorrect!
*To:	Shenzhen Merrytek Technology Co., Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	On Off Function Sensor
Brand Name:	Merrytek
Model Number:	MC098S 1
Certification:	CE, RED
Place of Origin:	Shenzhen, China
MOQ:	100pcs
Price:	Negotiable
Payment Terms:	T/T
Supply Ability:	10000 pcs/month
Delivery Time:	1, Sample and small order: Within 5 working days after receiving your payment. 2, Bulk order: 4-5 weeks after receiving deposit.
Packaging Details:	Bubble bag+Clapboard + Carton(K=A)
Rated Voltage:	220-240Vac 50/60Hz
Stand-by Power:	≤0.5W
Output Signal:	ON/OFF
Working Frequency:	5.8 GHz ±75MHz, ISM wave band
Mounting Height:	3m (6m Max)
Lifetime:	5 years warranty@Ta