Manual Control 60811 IEC Test Equipment Cold Bend Testing Apparatus
|
... Methods for general application-Test at low temperature clause 8.1 and 8.2 and figure 1. Figure 1 Cold Bend Test Apparatus Application: This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a...
HJ AUTOMATIC CONTROL TECHNOLOGY CO., LTD
|
Cold Bend Test Apparatus SUS304 Electrical Safety Test Equipment
|
Cold Bend Test Apparatus IEC60811-1-4 for Cable Made by SUS304 Stainless Steel 1. Introduction The cold bend test apparatus is designed according to IEC60811-1-4 clause 8.1 and figure 1, IEC60884-1, VDE0472, GB2951.4 and GB2099-94. It is applied to the test......
Pego Electronics (Yi Chun) Company Limited
|
IEC 60598-2-21 Figure 2 Cold Bend Test Apparatus To Measure Dynamic Bending Performance Of Wire And Cable
|
...Test Machine Overview Product description This Cold bend test apparatus is used to measure the dynamic bending performance of wire and cable under low temperature conditions, and is suitable for outer diameter less than or equal to 12.5mm round wire and cable or round insulated wire core is the wire and cable industry to test the bending......
KingPo Technology Development Limited
|
manual IEC Test Equipment IEC 60811 Cold Bend Test Apparatus For Cables Sheaths And Insulation
|
... bending performance of wire and cable at low temperature. The equipment is mainly composed of low temperature thermostat, winding device and material testing system. It is suitable for circular wire and cable with outer diameter less than or equal to...
Guangzhou HongCe Equipment Co., Ltd.
|
Cold Bend Test Apparatus For Cables ≤Ø 12.5mm IEC60811-1-4 Clause 8.1 And 8.2
|
Cold Bend Test Apparatus For Cables ≤Ø 12.5mm IEC60811-1-4 Clause 8.1 And 8.2 Product description: This device is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a major axis dimension up to and including 20 mm. According to the standard IEC60811-1-4 clause 8.1 and 8.2, common test......
Sinuo Testing Equipment Co. , Limited
|
IEC 60702-1 Clause 13.6 Electric Vehicle Cables Bending Test Apparatus
|
... to the standard requirement of IEC 60702-1 clause 13.6, and etc. It is used to test the bending performance of copper core or copper alloy sheathed mineral insulated general wiring cables to verify their reliability. It uses the motor to ......
Sinuo Testing Equipment Co. , Limited
|
IEC60851-3 Bending Test Apparatus For Flat Wires With Test Bars
|
...bending test apparatus is applicable to the bending test of various enameled flat wires, paper wrapped flat wires, glass fiber wrapped flat wires, film wrapped wires and other electromagnetic wires with a wide edge of less than or equal to 16mm, as well as the corresponding copper and aluminum flat wires. Major Technical Parameters Bending......
Advanced Instruments Co.,Limited
|
Luminaries Testing IEC60598-2-21 Cold Bending Test Device
|
...test whether the wire or rope lamp has cracks when it is wound at low temperature. The lamp is wound on the appliance shown in Figure 2, with a winding diameter of 4-5 times its own ......
SKYLINE INSTRUMENTS CO.,LTD
|
Figure 2.8 Plug Socket Tester Pin Bending Test Apparatus
|
...Bending Test AS / NZS 3112 Figure 2.1 dimensions of plugs Figure 2.2 apparatus for flexing test Figure 2.3 form of pin Figure 2.4 dimensions of insulation on insulated live pins Figure 2.5 pressure test apparatus for insulation on insulated plug pins at high temperature Figure 2.6 impact test apparatus for insulation on insulated plug pins at low temperature Figure 2.7 abrasion test apparatus......
Guangzhou Shice Equipment Co., Ltd.
|
Stainless Steel Cable Testing Machine , Electric Cable Cold Bending Test Machine
|
Cold Bending Test Machine HDX1307 Standard:IEC60811-1-4 clause 8.1 and 8.2, common test methods for insulating and sheathing materials of electric and optical cables-part 1-4:Methods for general application-Test at low temperature. Application:This test is intended in general for cables with an overall diameter up to and including 12.5 mm, or for flat cables, a major axis dimension up to and including 20 mm. Test......
shanghai kerang technology co ltd
|
Submit your “cold bend test apparatus” inquiry in a minute :